Whirlpool washing machines Error Codes

Whirlpool front-load washers use paired F/E codes for specific cycle problems. The current Product Help table gives useful owner checks for water flow, draining, dispenser operation, door locking and motor-speed sensing.

Before you use this table: Whirlpool publishes many more model-dependent F/E codes. This table keeps to codes with clear public owner checks; use the model manual for anything else.

Leading zeros, dashes and spacing do not matter: E01, E-1 and E1 find the same row.

Manufacturer-documented Meaning taken from a manufacturer manual or support page.   Reported Consistent owner and technician reports; the manufacturer has not published this code. Confirm with them if it matters.

CodeWhat it meansWhere to look first
F5 E2Also shown as: F5E2Whirlpool front-load washers; confirm with the model manualManufacturer-documented

The door is not locking properly.

Likely causes

  • Item obstructing the door
  • Door not fully closed
  • Lock problem if obstruction is ruled out

Source checked 2026-09-19

  1. Remove anything caught in the door and close it fully
  2. Use the model reset sequence only as Whirlpool describes
  3. If the code returns, arrange model-specific diagnosis

Washing Machine Troubleshooting: Diagnose Common Problems by Symptom →

F7 E1Also shown as: F7E1Whirlpool front-load washers; confirm with the model manualManufacturer-documented

Motor-speed sensing error; the washer cannot reach the speed expected for the selected cycle.

Likely causes

  • Shipping bolts/spacers still fitted on a new installation
  • Overloaded washer
  • Motor/drive sensing fault if installation and load are correct

Source checked 2026-09-19

  1. If the washer is newly installed, confirm all transit/shipping bolts and spacers were removed exactly as the installation guide shows
  2. Reduce an overloaded wash
  3. If the code returns with a normal load, use model-specific service guidance

Washing Machine Not Spinning? Diagnose the Real Cause →

F8 E1Also shown as: F8E1, LO FL, LoFLWhirlpool front-load washers; confirm with the model manualManufacturer-documented

The washer is sensing too little incoming water.

Likely causes

  • Water supply valve not fully open
  • Kinked inlet hose
  • Restricted inlet flow
  • Incorrect hose installation on models that require both hot and cold supplies

Source checked 2026-09-19

  1. Confirm the household water supply valves are fully open
  2. Check inlet hoses for kinks
  3. Check the installation instructions for the exact model before changing the hose arrangement

Washing Machine Troubleshooting: Diagnose Common Problems by Symptom →

F8 E2Also shown as: F8E2Select Whirlpool front-load washersManufacturer-documented

Dispenser-system problem.

Likely causes

  • Detergent drawer or cartridge clogged with detergent
  • Dispenser system not operating correctly

Source checked 2026-09-19

  1. Clean the dispenser only as the model manual describes
  2. Make sure detergent has not hardened or built up in the drawer/cartridge

Washing Machine Troubleshooting: Diagnose Common Problems by Symptom →

F9 E1Also shown as: F9E1Whirlpool front-load washers; confirm with the model manualManufacturer-documented

Drain time is longer than expected.

Likely causes

  • Kinked or clogged drain hose
  • Incorrect standpipe/drain-hose installation
  • Blocked pump filter on models that provide one
  • Excessive suds delaying drainage

Source checked 2026-09-19

  1. Check the drain hose for kinks and blockage
  2. Check the hose/standpipe installation against the exact model instructions
  3. Clean the accessible pump filter if the manual provides one
  4. Use the correct HE detergent and dose if oversudsing is present

Washing Machine Not Draining? Diagnose the Real Cause →

Code not listed? Not every brand publishes its codes, and we only list meanings we can trace. Two things help:

Sources and when they were checked

Codes can vary by model and generation. If the wording in the manual for your exact model differs from this table, follow the manual for that machine.